Modelcheck config files - heirarchy
Currently setting up ModelCheck config files (at new company). Looking at all i detail for the first time in a few years. Much is documented well by PTC but some are still not. In the Start files...
View ArticleRe: Creo Simulate Results Area for Improvement
Please post ideas for these improvements so I can vote them up
View ArticleClik here to view.
Re: Non-symmetric results for symmetric model and load?
John, I made a tube and fixed at one end just to show that Simulate will deform properly under a pressure load
View ArticleRe: Von Mise stress higher than Max Principal Stress?
Ups? Yes, I was totally wrong about this. Von Mises stress can be QUITE HIGHER than principal stresses. Why? Principal stresses are a three dimensional representation of the stress state of a point,...
View ArticleRe: Von Mise stress higher than Max Principal Stress?
THIS ANSWER HAS CRITICAL MISTAKES, REFER TO THE BOTTOM OF THIS POST, VON MISES STRESS CAN BE HIGHER THAN PRINCIPAL STRESSES.
View ArticleRe: Von Mise stress higher than Max Principal Stress?
THIS ANSWER HAS CRITICAL MISTAKES, REFER TO THE BOTTOM OF THIS POST, VON MISES STRESS CAN BE HIGHER THAN PRINCIPAL STRESSES.
View ArticleClik here to view.
Re: Creo Simulate Results Area for Improvement
Annoying isnt it? You could try creating mapkey for the sequence, that will do it.
View ArticleRe: Von Mise stress higher than Max Principal Stress?
Ruben Alejandro Villarreal Barrios wrote: Let's say that you graph the ellipse formed by the Von Mises stress equation. Can you graphically find the Von Mises Stress parameter? For example, when you...
View ArticleClik here to view.
Clik here to view.
Re: Simulate Results Definition (.rwd) Files
Eric, You cannot insert a saved results window, but I kept playing around with Creo 3, and you can Copy a result window and it will put it in the results window while keeping the original. Then you...
View ArticleRe: model/assembly parameter as variable in a optimisation study
Hi Erik, I tried to solve the problem as you proposed and it works!Many thanks for the great tip! BR, Franci
View ArticleRe: Simulate Results Definition (.rwd) Files
Thanks Steven I use the copy a lot, started to like it.Also an easy way to compare different studies. Then you have to remove the title text though, to let it insert the correct titleErik
View ArticleClik here to view.
Hyperelastic material with contact – looking for the best approach
Dear Creo simulate users. I would like to simulate one structure touching another structure. Once the contact happens the rubber part is deformed at the same time that the shaft bends.I would be...
View ArticleClik here to view.
Re: Apply load to pin joint of part in a constant direction and allow...
Giulio, Yes. The response I have had : One has to enter the value for Theta in RADIANS and check the 'Interpret Angular Translations in Radians' This raises the question regarding what the units of...
View ArticleRe: Fastener separation stress
Steven, Yes I agree they are updated and the account for stiffness check box does exactly what it is intended to do. BUT the software keeps the required preload values secret. ... unless I have missed...
View ArticleClik here to view.
Re: Hyperelastic material with contact – looking for the best approach
If you say the shaft bends, that would mean there is movement of one of the parts in the XY-plane in your 3D-model?In that case you cannot use the rotation symmetric 2D-model, because that is limited...
View Articlemsengine.exe error
Has anybody had, msengine.exe error whilst running simulate, we are running external pressure and tensile loads.
View ArticleClik here to view.
Re: Hyperelastic material with contact – looking for the best approach
Thanks Patrick I think your explanation made me understand why I was having some good results in one 2D axisymmetric problem but bad results in this one. I had another model (with good results) that...
View ArticleRe: Hyperelastic material with contact – looking for the best approach
A couple of thoughts: Are you using a mapped mesh? It increases the manual effort in setting up the model, but may improve run-time.Just to check your hardware influences, could you post the "Memory...
View ArticleRe: msengine.exe error
Not an uncommon error, there might be more info in the summary file, or the log file.This error can for instance happen when the license to run the engine is not available. Please provide more info, or...
View Article