Re: Simulate Idea
Ruben, I was just wondering about your turbine blades. Are they uniform thickness, and can you shell them?
View ArticleRe: Simulate Idea
When you're in the aircraft overhaul and repair business, and when parts have become exhausted through supply channels, yes, we have a person that is dedicated to do just that.
View ArticleRe: PTC Simulate changes file type of other programs
Hello Stephen, if the posts from David helped you, don't forget to mark one as Correct Answer. This way the community will know the question is answered. Thanks, Gunter
View ArticleRe: Cluster/Distributed Computing für Creo Simulate?
Hello Bernhard, this is the regular distributed batch functionality from Creo Parametric.It allows to run tasks (e.g. a simulation analysis) on a remote host (server), while continuing work on your...
View ArticleRe: Question regarding my assembly and mechanism
There is never a guarantee someone will actually look into it and provide a solution.But from my experience you can increase the chance someone tries it, when you add the assembly (or better a...
View ArticleRe: Question regarding my assembly and mechanism
...or the discussion fell off the bottom of the page and didn't get noticed. If you go to the advanced post editor, you can attach files. It is best to save-as or backup as a zip file to make sure...
View ArticleClik here to view.
Analysis Challenge – 3D Reaction Pattern
Community, The below snippet shows the solutions for 3D reactions that was calculated in Excel. The spreadsheet follows the formulation of a NASTRAN RBE3 element. RBE3 element theory and how it...
View ArticleClik here to view.
Simple things sometimes just aren't
Hello, This is a problem I have managed to avoid or work around for years and annoyingly I have failed to retire before it came back again demanding a solution. I think it has been mentioned before but...
View ArticleRe: Simple things sometimes just aren't
The simplest way is probably to do hand calculations using lots of trigonometry to figure out the position of the pulley, then model that state in Creo Simulate.Or is there an objection against this...
View ArticleRe: Simple things sometimes just aren't
I think you're right Patrick. No objection per se. Create the locus of each tangent point, construct geometry to point loads in directions using datum points. I wanted to attempt to include the support...
View ArticleRe: Cluster/Distributed Computing für Creo Simulate?
Hi Gunter, THanks for the respons. Is an additional license available to split the load over multiple nodes?Are there any maximum values for RAM (64 GB for Creo 1.0?) and CPU cores Simulate can use?I...
View ArticleRe: Cluster/Distributed Computing für Creo Simulate?
Bernhard, You need a license for each node. Regards
View ArticleRe: How to make a analysis on oak
I don't know why I get that result either! And I accidentally attached the wrong model and erase it the model of the video . Somebody just marked something as right answer, is driving me crazy.
View ArticleClik here to view.
Re: Simulate Idea
Yes! Uniform thickness and I shell them, this was only an exaggerate mesh about the problem of removing material. I am still unable to use the FRT, it just doesn't appear. Can you upload the model of...
View ArticleRe: Finite friction blocks
Hi all, just last Tuesday I did a presentation about the new finite friction contact model in Creo 3.0 at the SAXSIM (SAXon SImulation Meeting, www.saxsim.de), Technical University of Chemnitz,...
View ArticleClik here to view.
Re: Analysis Challenge – 3D Reaction Pattern
Hmmmm. To quote another topic on this forum: "Simple things sometimes just aren't "
View ArticleRe: Finite friction blocks
Roland, A big thanks to that. You have answered the initial question. I repeated the '2 blocks' study in Ansys Re: Creo Simulate vs ANSYS Workbench contact analysis w. friction. But didn't follow it up...
View ArticleClik here to view.
Re: Apply load to pin joint of part in a constant direction and allow...
To hijack Donald's thread once more to update with info after back and forth discussion with CS. Case #12927694: "Enforced theta displacement constraints demonstrate unusual behaviour” 11.2.16...
View ArticleClik here to view.
Re: Apply load to pin joint of part in a constant direction and allow...
Oh dear, I have just spotted this. It probably makes no difference to the results but it doesn't help confidence.
View ArticleClik here to view.
Re: Analysis Challenge – 3D Reaction Pattern
I would give it a shot, but I don't even know where to start.
View Article