Re: Scanned data, singluar mapping
Charles, I too would be interested in this.I try to get the following: - If it is easily remodel in pro/e I go this route first - If I can get the part sent to me in Step file formate I go this route -...
View ArticleRe: Creo Simulate - Restricted to 5 frames for static stress results...
Hi Don, I assume that you are running a non-linear analysis, is that correct? If that is the case, then if Simulate were to support animating more frames than were computed, then the results shown...
View ArticleRe: Scanned data, singluar mapping
Hi Charles, Concerning your question 2: A singular element is one which is locally inside out. Ideally, they should never occur, but they do sometimes in locations where the geometry is particulary...
View ArticleRe: Creo Simulate - Restricted to 5 frames for static stress results...
Hi Tad, Yes, You are correct in what you said above.I would like the ability to display approximate linear interpolation for the frames that were not specified in the non-linear analysis where...
View ArticleRe: Creo Simulate - Restricted to 5 frames for static stress results...
Don, Good, I'm glad I got it right. I can't promise anything, but I've added your request to our requirements database. Tad DoxseePTC
View ArticleRe: Scanned data, singluar mapping
Thanks Tad, I will check that we can submit data (not our casting). Is there anyway of checking for inside-out elements before running, are these the 'approximated' elements? It may mesh with little...
View ArticleUser Created Programs
Is there a way in Mechanica/Simulate to write custom programs (like you can with FEMAP's API or ANSYS' APDL)? If there currently isn't, can anyone from PTC comment on whether this functionality could...
View ArticleRe: User Created Programs
Hi Shaun, Most Simulate functionality is supported in Creo TOOLKIT. Regards,Steve.
View ArticleUNABLE TO CREATE ROTATION CONSTRAINTS IN SIMULATE...!
Rotation Constraints are greyed out in Creo 2.0.I am unable to create rotational constraints for a assembly model which I am working.Anybody facing this issue?
View ArticleRe: UNABLE TO CREATE ROTATION CONSTRAINTS IN SIMULATE...!
Hi, Hope you are creating the mesh using solid elements like tetra, wedge or brick. These does not possess rotation degree of freedom. For specific requirements, you can have cylindrical/ spherical...
View ArticleRe: UNABLE TO CREATE ROTATION CONSTRAINTS IN SIMULATE...!
Thanks Shiva, I remember in earlier version (Pro/mechanica) we used to get this option.Does that mean these rotation constraints had no affect on the boundary conditions?
View ArticleRe: UNABLE TO CREATE ROTATION CONSTRAINTS IN SIMULATE...!
That's true......Till Wildfire series, one could add/modify rotational degrees of freedom. But even then, they were not considered in the algorithm. So, even if you define there was no effect. Due to...
View ArticleRe: Scanned data, singluar mapping
Thanks Don, I haven't tried any of the software you mention, I shall explore further.
View ArticleRe: Scanned data, singluar mapping
Tad, Still waiting on permission to submit data. In autogem diagnostics, the message 'Autogem has detected an element incompatibility across the highlighted curve. Adding points to the curve may help....
View ArticleRe: Creo Simulate - Restricted to 5 frames for static stress results...
In WF4, contact model results could be animated over any number of frames (provided a multiple of 4) regardless of number of loading intervals.. This wasn't always the case, in earlier versions (can't...
View ArticleRe: Optimization Running time
Thanks Stephen BerkelyI find the solution.there was a probelm in the installation.
View ArticleRe: Creo Simulate - Restricted to 5 frames for static stress results...
In WF 4, Mechanica supported contact with only small deformations. Back then, for animating results, we linearly interpolated the frames between the start and end conditions, even if the user...
View ArticleRe: Pro/M optimisation: "invalid model or geometry"
Hello Jonathan and Steve For all that have or had the "Recovering from invalid parameter values by cutting step size" problem, this does not necessarily stops the optimization but makes it sooooooo...
View ArticleNew blog posts
All, I posted a couple of new blog posts here. I hope you find them helpful. Tad DoxseePTC
View ArticleRe: Not Constrained Correctly?
It works now!!! Thanks for your help, I forgot to change my constraints.
View Article