Clik here to view.
Re: Creo 3 simulate M120 - 25% more calculation time
Hi Wolfgang, Are you seeing your simulations losing the license and regaining it by chance?Currently having this issue with Creo 3 M080 and Creo 4 PTC has not been able to reproduce the issue and the...
View ArticleClik here to view.
How to Constrain Surface of a Part in Assembly to be Free to Move in all...
Hi, I have a large assembly where I have used a simplified rep to exclude all components except one component and all of it's fasteners (solid models).The fasteners have preload assigned.I now want to...
View ArticleClik here to view.
Creo Simulate
Good Afternoon,I am trying to idealize loads on a simply supported beam as per the screenshot. The beam is sketched using two lines to idealize the loads.I am having trouble with the load on the second...
View ArticleSine Sweep in Dynamic Freq. Analysis
Hello.... I want to simulate a sine sweep in Dynamic Freq. analysis. I thought it would be easy to input it with a symbolic expression. I tried several expressions, all with no luck. I want F(x) ==...
View ArticleRe: Analysis done but "run status" is empty
It was due to an accent in the name of the folder. I change the name and it works.Thank you for your answer Domen Resnik !
View ArticleRe: How to Constrain Surface of a Part in Assembly to be Free to Move in all...
Hi,PTC's response was to use springs with different stiffness in two directions.I have created a new enhancement request. Click link below for enhancement request unless someone has another Idea of how...
View ArticleRe: How to Constrain Surface of a Part in Assembly to be Free to Move in all...
Mine maybe a duplicate request Simplify support definition / Enable contact with 'invisible wall'
View ArticleRe: Sine Sweep in Dynamic Freq. Analysis
Good Morning Paul. Thank you very much. "frequency" is the word. I was going nuts trying to do this. Thanks again. Rich Hilson
View ArticleCan anyone mirror this solid for me?
This is not directly a simulation topic, although the model is intended for simulation. Assuming I have friends in this forum, you might be more willing to help out, than in the modeling forum where...
View ArticleClik here to view.
Crushing a cylinder using creo dynamic simulation
Good morning all, I'm looking for some advice regarding running a dynamic simulation to crush a tube longitudinally. I have a couple of tubes which I'd like to crush so I can compare the effects of...
View ArticleClik here to view.
Rotation for part(s)
Hello, There is the "rotation" option under the "translation" but it doesn't operate so easily than the definition of translation. Why? How can I define a simple rotation (with certain angle value) for...
View ArticleClik here to view.
Re: Rotation for part(s)
Hi Roland, You can't directly apply rotations to solids, because (as I understand it) constraints actually apply to nodes, and nodes only have three DOFs, not six. Same thing applies to moments,...
View ArticleClik here to view.
Re: Rotation for part(s)
Hello Jonathan, ok, I have wrtitten that the using of rigid link is OK for the rotation. I define the rigid link between a point and a surface but it doesn't operate.This is my testmodel with...
View ArticleRe: Rotation for part(s)
A couple of thoughts: You seem to have tried both solutions at once. Either try the rigid link with a Cartesian constraint; or a cylindrical theta displacement applied to the outside edge of the end...
View ArticleRe: Crushing a cylinder using creo dynamic simulation
Hello Richard, MECHANICA (Creo Simulate) is not possible. regardspaul
View ArticleRe: Can anyone mirror this solid for me?
Thanks, much appreciated. I eventually managed to resolve it in SW but thanks anyway... geometry issue plus wrong technique...
View ArticleClik here to view.
Error - geometry preparation
Hello, I often have to use the "Extrude for volume region" option.It operates well in a lot of cases but there are some situations when it leads to error: I am using this function similar in every case...
View Article