Create point for command Total Load at Point
Hello!I would like to use the Total Load at Point,but I don't know how to create the point Can You help me? Thank you Regard
View ArticleClik here to view.
Re: Create point for command Total Load at Point
You can use a point that you created in the model, or you can create a point within the Mechanica (Simulate) model that won't show up when you exit Simulate. It's under Refine Model (in English at...
View ArticleClik here to view.
Error message with fasteners
Hello!Can you help me to understand this message? Thank you
View ArticleClik here to view.
Re: Error message with fasteners
It's just a warning message. By default, the mating surface between parts is considered as bonded. In other words, the whole mating surface is super glued together. Once you apply fastener, it will...
View ArticleForce constraints on natural frequency analysis
I've made a simple support structure on which about 150kg load is applied and the structure is attached to other frames.I did natural frequency analysis (modal analysis) on the structure itself for...
View ArticleRe: Mechanism Analysis - Constraint Failure
Chris, Unfortunately I will not be able to share a model with you. I have talked to some people who are quite experienced in mechanisms, and they said they don't think there is a way to tell Creo's...
View ArticleEngineering vs True stress-strain?
Hello, We're attempting to perform a analysis using a non-linear hyperelestic material (similar to santoprene) using Creo 3.0 M070. We have the engineering stress strain data for import, but I've...
View ArticleClik here to view.
Re: Error message with fasteners
Federico, I have attached an old document that depicts why springs are added, and this may be viewed on Pages 9 and 10. Creo has made a lot of improvements since this documents was released, but the...
View ArticleRe: Trace of curves of results
Sorry, I'm not understanding. Perhaps you could post in French so that I can attempt to translate from there, and choose my own alternative meanings?
View ArticleRe: Trace of curves of results
You can try by putting a hard point where you want to stop it.
View ArticleRe: Trace of curves of results
Ican'tchooseonestoptodrawacurve. Sur un cylindre il n'y a pas d'arrête à choisir pour faire le tracé de la courbe des déformations ou contraintes.
View ArticleRe: Trace of curves of results
Google gives me "On a cylinder there is no edge to choose to draw the curve of the deformations or stresses." 'Edge' makes more sense to me than 'stop'... why doesn't my surface region idea work to...
View ArticleRe: Trace of curves of results
Yes,it'sanideaIwilltrythissoon. Edgeisbetter,butIdonotspeakEnglish,soIgothroughatranslatorAutomatictoreadandwriteandItrusttheresultsabittoo.
View ArticleRe: Force constraints on natural frequency analysis
example / modal prestress regardspaul
View ArticleRe: Force constraints on natural frequency analysis
Thank you, Paul!I should've used prestress modal analysis... One more question. When do you need gravity load on the analysis? Thank you again! Seong
View ArticleRe: Force constraints on natural frequency analysis
big effect by prestress: pretension is applied to ropesand gravity load is transversely example regardspaul
View ArticleRe: Error message with fasteners
Best practices for fasteners: http://support.ptc.com/help/creo/creo_sim/usascii/#page/sim%2Fsimulate%2Fbestpractice%2Fbest_practice_fasteners.html%23
View ArticleClik here to view.
Creo 2.0 Simulate Lite Analysis - 'Cannot find engine output file'
Hello community,I was super optimistic after getting some valid-looking stress results after applying some load to a platform I'm trying to evaluate (Using Creo 2.0 Simulate Lite - Student License, and...
View ArticleRe: Creo 2.0 Simulate Lite Analysis - 'Cannot find engine output file'
Hi Martin, Please submit your request in "Academic Support Request" form: Academic Case Logger
View ArticleClik here to view.