Clik here to view.
Re: How to measure force in dynamic Time and frequency analysis?
Thanks, smart solution.
View ArticleClik here to view.
Suppressed connections
Hi All I am trying to simulate a gear mechanism. But I get this error : The highlighted connections are not defined from two bodies, if you continue they will be suppressedI have figured it out that...
View ArticleRe: Suppressed connections
Hello Farzad, If I understand correctly, then you face this problem when you are switching from Parametric to Simulate. isn't it? May be you can try this:This issue occurs when the model is over...
View ArticleRe: Suppressed connections
Hi Torabi, When defining a mechanism connection all references / constraints need to be between two parts only.example:rotation constraint: between hole or axis in part A and in part BVertical...
View ArticleClik here to view.
What causes Creo Simulate to not show analysis in the analysis definition...
Hi, What will Creo Simulate to not show analysis in the analysis definition dialog box and how do I get them to show again? Creo Parametric Simulate 3.0 M080 Thanks,Don Anderson
View ArticleRe: What causes Creo Simulate to not show analysis in the analysis definition...
Make sure that your working directory is set to where the analyses are. If they still don't show, we had an instance recently where there was an unusual character in the path to the directory which...
View ArticleRe: Suppressed connections
Thank you so much. So if the part A is connected to the motor, and the part B is the follower, the part A should be inserted in the assembly tree , in a higher point regarding to part B ? cause when I...
View ArticleClik here to view.
Re: Plate bending
I have created some simulation to investigate the behaviour of material (stress distribution) after the reach of yield stress. (My material model is defined by a measurement)I have a simple measurement...
View ArticleClik here to view.
Re: Plate bending
hello Roland i used perfect plasticity: technical curve is not real: regardspaul
View ArticleRe: What causes Creo Simulate to not show analysis in the analysis definition...
Might also be that the full path name for the directory is too long? That's a problem that happens in the manufacturing package when outputting toolpath files. I don't know what the character limit is,...
View ArticleClik here to view.
Re: weigthed link, unreal simulate results
Paul, Just to says thanks for the school, I have not been able to review all your examples, I just have been busy with other stuff, as soon as I try any of your suggestions i will post it Charles, ok,...
View ArticleClik here to view.
Re: Plate bending
OK, I tried the perfect plasticity model, the stress value did not reach the ultimate stress, but actually it is not possible caused by the perfect plastisity model: If the stress value is higher than...
View ArticleClik here to view.
Clik here to view.
Re: Extract measures data to plot in Excel
Richard You can save a graph as an excel file (file, save as, select excel in the box right below) You can change the axes like this: Format -- Edit change each of the axes to log scale Hope this...
View ArticleClik here to view.
Re: Creo 3 simulate M120 - 25% more calculation time
SORRY, Test not correct!!! Creo 3 M130 is wrong too:
View ArticleClik here to view.
Re: Creo 3 simulate M120 - 25% more calculation time
Wolfgang, i think it's a problem of parametric (pdf attached) Creo Parametric M060-M110: M120 and M130: multithreading disabled regardspaul
View ArticleClik here to view.
Fatal Error due to memory?
Good Morning Can you help me to fixed this problem?Thank you Best Regards Federico
View ArticleClik here to view.
Re: Fatal Error due to memory?
You could try to increase the size of the Windows paging file and hence increasing the virtual memory available to the software. In Windows 10 you can open an explorer window and select "This PC".Then...
View ArticleClik here to view.