Re: Symmetry constraint question...
A mirror symmetry in structural will just be ignored in thermal. A "mirror" in thermal assumes no heat flux (insulated) through the mirror plane, which is already the default by doing nothing to the...
View ArticleRe: Symmetry constraint question...
So when you say 'the default be doing nothing to the surface', are you saying that there is no need to apply a symmetry constraint to the mirrored surfaces? I guess because creo is solving for heat...
View ArticleRe: Symmetry constraint question...
Yep, that's how I understand it. My reference books say the same thing.
View ArticleRe: Symmetry constraint question...
Mirror symmetry is not supported in Thermal mode....only cyclic symmetry can be utilized.....for your application, for a quarter size, cyclic symmetry can be applied.....and it has to be applied in...
View ArticleCylinder analysis in CREO 2.0
Hello All I want to simulate a cylinder head(A) and base(B) assembly unit to check the structural integrity under working loads. I Am new to CREO. HEad unit (Part A) is threaded into base unit (Part...
View ArticleRe: The Most Worthless Error Message
No that's not hte most useless error message, this one is more useless: An engine disk write error has occurred, probably due toinsufficient disk space or directory/file permissions. Mainly becuase the...
View ArticleRe: Cylinder analysis in CREO 2.0
Hi Vinay, If you're not concerned about the stresses in the threads, you could just apply a pressure distribution in the lower cavity using a 2D axisymmetric analysis while capping off the top of...
View ArticleRe: Cylinder analysis in CREO 2.0
HEllo Steve THanks for your reply.I am Not concerned about the stress in threads. HOwever what is happening is the internal pressure in part B causes deformation radially thereby loosing the thread...
View ArticleRe: Cylinder analysis in CREO 2.0
In that case, it appears you would have to split the model down the axis of rotation and create a 2D model with threads in contact.
View ArticleRe: Cylinder analysis in CREO 2.0
Steve THanks for your reply. I Will try modeling the threads with contact.
View ArticleRe: Datum Point in creo simulate and creo parametric
It shouldn't matter, but keep in mind that you can't pattern or mirror datum points on the simulate side.
View ArticleLightweight Weld feature recognition in Creo Simulate
Is there any way to convert Lightweight weld features to Surface weld features?Is there any solutions/ workarounds suggestions/practices?
View ArticleRe: Datum Point in creo simulate and creo parametric
If you need a datum point to affect the mesh (whether created in Creo or Simulate), don't forget to make it a 'hard point' using Autogem controls otherwise it is ignored.
View ArticleRe: External Analysis tutorials?
Thank you for your suggestion Shiva, I will take a look at the demo version.But I am still looking for examples of "external Analysis" application, because in the end I am not the one deciding which...
View ArticleRe: External Analysis tutorials?
"With the External Analysis tool, you can create a customized analysis within Pro/ENGINEER to run commands that drive external software. The analysis provides five different steps in the following...
View ArticleClik here to view.
Re: External Analysis tutorials?
Hello David, Looking at the link below, I understand that the lack of documentation on "external Analysis" is still an open...
View ArticleDrop test simulation - Mechanism damping
Hi PTC Fellows, I need help for my Mechanism simulations. I'm working on a drop test analysis. This means the impacts between the granite/concrete/steel blocks and danamid/aluminium specimens. Creo...
View ArticleRe: External Analysis tutorials?
Stephane, If you have the Ansys 14 CAD Interface license you will be able to link the ansys session directly with the creo 2 session and use Ansys to perform the CFD analysis and drive modifications to...
View ArticleRe: External Analysis tutorials?
Thank you Don, but what I am trying to do is different: I want to use the model optimization capabilities of CREO2.0 using the value (in my case the pressure gradient) calculated in Ansys CFX as the...
View ArticleRe: External Analysis tutorials?
It seems like the external analysis is setup for situations where the typical communication between Creo and the other program is conveniently handled by a fixed set of numbers. Since the trigger is a...
View Article