Re: User need help with Simulation setup.
David, A quick look and the following comments ... Model is symmetric, cut it in half. This will reduce the number of contacts and provide a model that is easier to constrain.You have tried to...
View ArticleClik here to view.
Re: User need help with Simulation setup.
Had a quick try with the above mods, and made up materials similar to notes in earlier posts (none in model) I ran in Creo 3 (for convenience). but used only functionality you have. Mesh used leaves a...
View ArticleRe: Piece weight permanently displayed.
I agree with David:The current mass is shown by the system mass parameter and the original mass probably has been just added as a fix text or it exists as a parameter in the model that does not change...
View ArticleRe: Fix displacement in only +ve direction for non-linear analysis?
Hello Sumit, did the hints from Steven and Shaun help you? Gunter
View ArticleRe: User need help with Simulation setup.
David, If you're on maintenance with PTC, then I would upgrade to Creo Simulate 3.0, which has LDA (large deformation analysis) with contact.
View ArticleRe: How export Creo Simulation results in word format?
I want to say something ,but i just learn to windchill and .... 好想发个哭的表情
View ArticleClik here to view.
Re: User need help with Simulation setup.
David, I took a quick look at the geometry in the assembly. It appears that you have two planes of symmetry, and you could reduce the assembly to 1/4 for FEA. Also, there are too many small rounds...
View ArticleRe: User need help with Simulation setup.
First of all, this is a problem that needs to take contact AND large deformations into account, and this is not available in ProEWF5/Creo Elements Pro, Only in Creo1 and later. The problem is close to...
View ArticleEurocode 3 anyone?
I have an assignment where I need to analyze a structure and have it approved according to the Eurocode 3 standard. It is a rather simple steel frame that serves two functions. It is used for...
View ArticleRe: Eurocode 3 anyone?
i don't think you can use a FEA analysis for eurocode due to stress concentrations (artificial in the fem software). EC3 basically gives you the allowable stress (sigma zulässig) for the given usage...
View ArticleRe: Eurocode 3 anyone?
I can use different techniques to refine the FEA model so that it correctly calculates stresses in critical regions. That's just a matter of how detailed/complex I want to make the model. So the stress...
View ArticleRe: User need help with Simulation setup.
Thanks all for the postings - everyone comments are very helpful. Everyone of this forum - I am honor to get to know - I am glad to be a member of this forum. To answer the Creo/Elements Pro simulation...
View ArticleRe: User need help with Simulation setup.
David, Could the client load Creo View? This would enable you to output model info and analysis results and they coutd review that way? It would augment any paper delivery you intend. Regards Charles
View ArticleRe: How to calculate bearing load
Amit, Can you describe your problem with some more detail? You show an assembly and a several levels of detail finer than one would consider unless modelling a bearing as per your attached image if in...
View ArticleRe: Color of the mesh elements
Help ! Hi Users, we encountered from WF5 to Creo 2.0 stuttering displaying performance of meshed parts/assemblies with solids. It can't be our 5000€ workstations with 10 GHz, 32GB RAM and 2000€ Nvidia...
View ArticleRe: Fix displacement in only +ve direction for non-linear analysis?
Hello Gunter, As mentioned previously I was out of office until today and I appologise for the delay in reply.I am not yet satisfied with the suggestions and am looking forward to further refinement.
View ArticleStuttering mesh displaying
Help ! Hi Users, we encountered from WF5 to Creo 2.0 stuttering displaying performance of meshed parts/assemblies with solids. It can't be our 5000€ workstations with 10 GHz, 32GB RAM and 2000€ Nvidia...
View ArticleRe: Color of the mesh elements
Please, explain better your problem.I use Creo 2 to work standalone only for FEA problems, and all I saw are better performances (workstation HP Z620, Win7).As in wildfire editions, to view the mesh...
View ArticleClik here to view.
Re: Stuttering mesh displaying
Hi Andreas, 10 GHz - that's quite some overclock! Are you sure? In general I've found that Creo has some improvements in the code when displaying edges in 'normal' modelling mode, but I haven't tried...
View ArticleRe: Fix displacement in only +ve direction for non-linear analysis?
Can you upload the model?
View Article