Re: can it is possible to create thermal and structural analysis in Creo...
Short answer: Yes. Long answer: you need to give more details about what you want to do, to get a better answer.
View ArticleClik here to view.
Re: Mechanica analysis run error with 'internal engine error'
As to my case, the two parts are connected wtih no distance, then what setting is suitable for it? And if pulled away, what difference will be to the results?
View ArticleRe: Mechanica analysis run error with 'internal engine error'
Bonding something and defining a contact region is not the same thing. Bonding something is like welding it together. There will be no localized stresses at the interface. When you define a contact...
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
As Patric mentioned, you need to provide more detail, but you probably want to look into defining your thermal analysis and then you can bring it into the structural analysis as a MEC/T load.
View ArticleRe: Mechanica analysis run error with 'internal engine error'
Bonded: the separate parts will act as if they were one part. They are bonded or 'glued' together. This means that if you pull the parts apart, the parts will not separate and you will get tensile...
View ArticleRe: Mechanica analysis run error with 'internal engine error'
As to my case, there is friction at the contact surfaces. When applied tensile force as shown in figure, the cable tie will deform and generate relative silde between the contact surfaces. In Pro/e...
View ArticleRe: Mechanica analysis run error with 'internal engine error'
Thank you very much! Only in PTC community can I find my desired answer.
View ArticleHow to animate hook movement
Does anyone know the easiest way to animate the movement of a hook.The hook is placed on a lid and snaps into a base.The lid is constrained with an opening angle in the assembly. The hook in the lid is...
View ArticleRe: Mechanica analysis run error with 'internal engine error'
In Creo 3 there is an option to define contact with finite friction. You can set a static and a dynamic coefficient of friction.I haven't tried it, so can't help you any further with this.
View ArticleClik here to view.
Re: How to animate hook movement
Do you have a picture of all this? A picture says more than a thousand words!
View ArticleClik here to view.
Re: MDO - How to know the torque of a motion
@Hi Aitor Apply the servo motor on the shaft where you like to analyse the torque:... and you can measure the torque ... : BR - Urs
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
Is it possible to do a multiphysics problem - in other words, can I solve a problem that has combined structural and thermal loads? I see 2 separate modes in the software (structural AND...
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
Is it possible to do a multiphysics problem - in other words, can I solve a problem that has combined structural and thermal loads? I see 2 separate modes in the software (structural AND...
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
Yes, you can bring in the thermal results via a MEC/T Load.
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
Yes!! But is it possible in Basic Simulation module or required any Addon
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
It is not an Add-in or external program. It is built into the Creo simulation package. If it isn't turned on for you contact your PTC rep and find out what package you need to turn that feature on. I...
View ArticleRe: can it is possible to create thermal and structural analysis in Creo...
Ok no worries! Thank you Christopher
View ArticleMechanism Constraints could not be satisfied...
The Mechanism could not be assembledWhen you receive this, apparently unhelpful, message, how do you fault-findthe assembly?I have a reasonably simple assembly, which moves as I want it to when I...
View ArticleClik here to view.
Mechanism Constraints could not be satisfied...
Fixed it!I was trying to motorise the wrong thing. I drove my pulleys and it allworked.thanks anyway.regards,JohnThis email, including any attachment, is a confidential communicationintended solely for...
View ArticleClik here to view.
Re: Stress analysis simulation on welded parts
Model weld as separate solid part. Define bonded interface between part /weld. Also define contact interface between both parts or surfaces. So that the parts are ''merged'' using weld part.The weld it...
View Article