Re: Running Simulation on a assembly with complex geometry
In addition to what Chris suggested, try setting the default contact setup to free and see if the assembly meshes. This helps determine if the issue is with the mesher trying to get a contiguous mesh...
View ArticleRe: Thermal analysis - travelling heat loads
1. My guess is that the parameter 's' is a position value on a path length and 'time' is of course time. The exponential decay function is used to represent how the heat load moves along the path...
View ArticleClik here to view.
pdf book regarding analysis & simulation
***... I am just a beginner in PTC CREO SIMULATION. can any one give me link for a PDF e book on analysis & simulation. Thank you
View ArticleClik here to view.
Re: Is it possible to calculate a plate of glass support on the four corners?
Denis, The four interfaces represents the four contact zones (shown below).1. One contact between the glass and the support2. Three contacts between the glass and the rounds on the support. You can...
View ArticleRe: pdf book regarding analysis & simulation
Hi allYoucanwatchonthisdiscussion.Kind regards.Denis. https://www.ptcusercommunity.com/thread/54475
View ArticleClik here to view.
Re: Is it possible to calculate a plate of glass support on the four corners?
HelloSteven,Thanksforthereply.OwnweightwithgravityIknow. ForthefourpositionsI haveunderstood,thefactof taking1/4oftheplatetoreprinted4timesthesupportcontactforthesimulation.Kind regards.Denis.
View ArticleClik here to view.
Re: Is it possible to calculate a plate of glass support on the four corners?
HelloSteven,Inthecaseof aplatewiththesedimensions,shouldyounotusethemethodofshells?Kind regards.Denis
View ArticleClik here to view.
Re: Is it possible to calculate a plate of glass support on the four corners?
Hello, shells only without large deformation. RegardsPaul
View ArticleCREO 3.0 Mechanism Dynamic Option
Hi all, I am trying to use CREO MDO to get the torque needed to put an assembly in rotation considering acceleration, masses, frictions and so on. I think that the model is well implemented but the...
View ArticleClik here to view.
Re: How can I change the unit of measure in the Linearized Stress report?
Marco, You change the units to MPa (mm-N-s) for the linearized stress report in the model properties before running the analysis. The below report has units of MPa.
View ArticleRe: Is it possible to calculate a plate of glass support on the four corners?
HelloPaul,Thankyouforyouranswersandyourexamplesofsimulations.It isinterestingtoseeyourapproachforthesimulationofthetwo...
View ArticleRe: Is it possible to calculate a plate of glass support on the four corners?
Denis, Why are you concerned about the arrow?
View ArticleRe: Is it possible to calculate a plate of glass support on the four corners?
Steven,It istoalreadyhaveanideaoftheshapetheglassplatewill takeunderitsownweight,asthiswill beashelf.
View ArticleClik here to view.
Re: Is it possible to calculate a plate of glass support on the four corners?
Steven,Andit ismainlytheonlyconstraintthatonelittlemeasurewithoutappliancesSpecialgaugesconstraints,etc.
View ArticleSelect Volume Region for Max Prin Strain Measure in Creo Parametric Simulate...
Hi, Please confirm that it's not possible to select a Volume Region in a part for a Simulate measure of Max Prin Strain while in Creo Parametric Simulate 2.0 (m120) ?Trying to use a volume region for a...
View ArticleClik here to view.
Re: Select Volume Region for Max Prin Strain Measure in Creo Parametric...
Don, I cannot in 2.0 M100I can in 3.0 M060 Looks like a Creo 2 limitation. bfn Charles
View ArticleRe: Select Volume Region for Max Prin Strain Measure in Creo Parametric...
Charles,The only way I found that I could do it was to first assign the volume region to a layer and then select the layer for the measure.
View ArticleGlobal sensitivity output
Hello All, Is there a config option (hidden or otherwise) to persuade Creo to output FULL results at each step of a Global Sensitivity study? I know GS studies aren't meant for this but you don't know...
View ArticleRe: Select Volume Region for Max Prin Strain Measure in Creo Parametric...
Don, Nice one. Perhaps you should mark yourself as correct and get the star for tenacity?
View Article