Clik here to view.
Re: Non-symmetric results for symmetric model and load?
Jerzy, great work,geometry description is wrong, all revolve simulate-features, torus too. Regards,Paul
View ArticleClik here to view.
Re: Non-symmetric results for symmetric model and load?
Erik, revolve feature in STRUCTURE is inaccurate: this "ERROR" is 30 years old. Paul
View ArticleRe: Constraints for a roller to follow a curved path in a cylinder.
The roller is supported on the slot in the cylinder. Could I find out the forces acting on the roller when I make this kind of an arrangement?
View ArticleHelp with constraining rollers on cylindrical surface
Hi Guys, I’m having huge problems with constraining this assembly…The force is applied to the end of the crane via a long shank eye bolt, and the bottom of the crane is fixed in position. The first...
View Articleset-up of Simulate
First off, forgive me, I am new at the simulate side of things.I am attempting to do the middle man admin of the software setup and I am looking for some insight.I need to do an accelerated knowledge...
View ArticleClik here to view.
Re: Help with constraining rollers on cylindrical surface
Are you using a contact interface between the rollers and the upright cylinder? Where is the area of interst in terms of looking at stresses? Do you need to use contact on teh rollers or would some...
View ArticleRe: Help with constraining rollers on cylindrical surface
Hi Greg, Thanks for your reply. I am relatively new to CREO so I had to quickly search this up but when you say ‘contact interface’ do you mean just defining the constraints of the parts prior to...
View ArticleClik here to view.
Re: How can I change the unit of measure in the Linearized Stress report?
Marco, I think you would have to change the units to (mmNs) in the units manager before running the analysis in order to get MPa in the stress results window.
View ArticleClik here to view.
Re: How can I change the unit of measure in the Linearized Stress report?
Marco, It looks like there may be bug in the code when trying to plot the stress report using mm-N-s. The points won't activate for selection prior to making the report. There are two reports below,...
View ArticleIs it possible to calculate a plate of glass support on the four corners?
HelloWithSimulate,isitpossibletocalculateaplateofglasssupportonthefourcorners?Thearrowsandconstraints.Glassthickness3.0[mm] Dimensions952 x 680[mm]EV = 60.0 [GPa], mu = 0.225 [-], 2.530 density [kg/m ^...
View ArticleRe: How can I change the unit of measure in the Linearized Stress report?
I submitted a tech support case on this and furnished the model to PTC and here. FYI.
View ArticleRe: Is it possible to calculate a plate of glass support on the four corners?
Hi Denis, Are you asking is it possible to calculate a plate of glass that is "supported" on the four corners of the plate of glass without using the glass frame under a 1g load?
View ArticleClik here to view.
Re: Help with constraining rollers on cylindrical surface
Hi Sam, I think you may need to review all your 'interfaces' between the parts, and possibly simplify your model for analysis. AFAIK, assembly constraints have no effect in Simulate - all they do is...
View ArticleRunning Simulation on a assembly with complex geometry
How do you deal with situation when some of the components (cast) doesn't get meshed. When I run the AutoGem, it shows few surface which is causing issue. If I need to fix the model, its going to be...
View ArticleRe: Running Simulation on a assembly with complex geometry
Try meshing the part by itself. Try exporting the part and then re-importing it. Check your accuracy.
View ArticleRe: Running Simulation on a assembly with complex geometry
Which format to export ? I tried STL
View ArticleRe: Is it possible to calculate a plate of glass support on the four corners?
HelloPaul,Thankyouforthismagnificentdemonstrationonthisplateofglass.Withtherepresentationofthefeetandtransparency. It's...
View ArticleRe: Running Simulation on a assembly with complex geometry
Could you please elaborate on the process you are suggesting.
View ArticleRe: Running Simulation on a assembly with complex geometry
I was thinking Step but I don't think one format would work better than another. To be clear - the 3 suggestions I made were independent checks you could try. The 3 checks I suggested are things you...
View Article