Clik here to view.
Re: Anyway I can select just the top surface for my analysis?
I have attached a picture in this reply. Could you explain how do it set surface regions? I just need the top surface as well as the bottom but when I click the surface for the load it'll end up the...
View ArticleRe: Anyway I can select just the top surface for my analysis?
Look under the Refine Model tab. You can create both Surface Regions and Volume Regions. Basically, you sketch a profile (can be as simple as a single line to cut a surface) and then select one or...
View ArticleClik here to view.
Clik here to view.
Re: Reading Creo results
I saw your M080 question but would have had to download install ... always a job for later. I think I know what it is saying. It recognises the model being read is from a newer edition of the software....
View ArticleClik here to view.
Re: Anyway I can select just the top surface for my analysis?
I have tried splitting the surface region but when I put a force and tried running the analysis there is a problem that occurred and I'm not too sure what's wrong. attached below is the image of the...
View ArticleRe: Reading Creo results
I think it's modification of contact analysis: sim_contact_penetration: the meaning of this config.pro optionas well as the engine command line option (-contact_penetration) was different before Creo...
View ArticleRe: Simulate fastener questions...CSV columns and edge references.
I think that would be a correct assumption. Creo Simulate does not have functionality for counter-sink fasteners, and that's why I submitted a Product Idea to add it. SolidWorks has it, so the image...
View ArticleClik here to view.
Re: Anyway I can select just the top surface for my analysis?
Sorry, I don't have an easy answer for this. Mechanica sometimes throws up strange errors like this, with little useful explanation. Try changing the boundary position on the surface region, to begin...
View ArticleRe: Simulate fastener questions...CSV columns and edge references.
Thank you for your help. I have run some simple test cases and verified the small compressive forces that can be seen in the fasteners. It would be nice if PTC would allow for counter sunk geometry....
View ArticleRe: Anyway I can select just the top surface for my analysis?
Kong, First, do you have an error free mesh? You can mesh the model without running it. What does it look like?
View ArticleClik here to view.
How to turn off location coordinates of view max in results window?
Hi, Anyone know how to turn off the x y z coordinates for view max measurement in the results window in creo simulate 3.0? Thanks,Don Anderson
View ArticleClik here to view.
Re: How to turn off location coordinates of view max in results window?
I assume you're using the dynamic query function? If so, set the environment variable "sim_pp_query_location" to "no" in the Configuration Editor (File -> Options -> Configuration Editor).
View ArticleClik here to view.
Mechanism analysis
Hi All,I have a problem, where I want to analyse how slider block can affect the guide bar. I have looked through good few tutorials on YouTube but nothing seems to match.There is a welded frame where...
View ArticleRe: Anyway I can select just the top surface for my analysis?
Hi, so I have attached my part file and I have tried to change the surface region but I'm not sure I have done the right thing as it still shows the same problem. While i was running the mesh it always...
View ArticleClik here to view.
Re: Anyway I can select just the top surface for my analysis?
I have tried running mesh but it comes with the same error. Is there a problem with the surface that I have created?
View ArticleRe: Anyway I can select just the top surface for my analysis?
I can't open your file as you're using the Educational version; but from your last screenshot, it looks like the problem is with the 'edge' surface, not the top one. Because this surfaces touches...
View ArticleClik here to view.
Re: How to turn off location coordinates of view max in results window?
Hi Shaun, The switch you suggested had no effect.I'm finding since we switched to Creo 3 M080 that "View Max", "View Min", "Model Max", and "Model Min" always show the location of the stress in x,y,z...
View ArticleRe: Total Load at Point?
Dana, This requirement of an arbitrary point for applying moment loads doesn't make any sense whatsoever. Moments are always about an axis first of all, not a point. Second, how does choosing an...
View ArticleRe: How to turn off location coordinates of view max in results window?
Document number is CS221532. SPR is 4884837.
View ArticleRe: How to turn off location coordinates of view max in results window?
Thanks Steven!One would think they would think things through like this before making a change like this.I will press the issue from our side too.Don Anderson
View Article