Clik here to view.
Re: Nested computed measures?
Jonathan, "It appears that I can't calculate an 'interim' variable..." yes, it is not possible in simulate, but with BMX (extra licence). RegardsPaul
View ArticleClik here to view.
Re: Fix problem introduced in Creo 3 Creo Simulate fasteners and materials...
Need a SPR to restore functionality, but I voted up on the idea anyway. I suppressed one of the components in Parametric before switching to Simulate, as shown below. I didn't see the suppressed...
View ArticleRe: Fix problem introduced in Creo 3 Creo Simulate fasteners and materials...
PTC have confirmed what i found last week.I hope to have a spr when i talk to ptc the first week in January When i get back in the office. Thanks,Don Anderson
View ArticleClik here to view.
Cut in two piece
HelloIdoatestsimplywithawasher,seethesketchenclosed.Idothesimulationwiththewholepuckand thenwithhalfofthepuckas well ashalfoftheload.AndIgetnotthesameresulttoVonMises:Entirepuck750.0[MPa]Puck half...
View ArticleClik here to view.
Re: Quick question re. surface regions
... It seems that in Creo3.0 m110, the old fashioned method works again.
View ArticleRe: Cut in two piece
Hi Denis, Where are your stresses measured? Do the contact forces balance/add up? How is your F1 & F2 applied? atb
View ArticleClik here to view.
Re: Cut in two piece
Good morning Charles.In reality the force F1 is the support reaction of the force F2. I have an F1 support that is done on a dia crown. Ext of 42.0 [mm] and dia int of 30.0 [mm].The force F2 of 30 [KN]...
View ArticleClik here to view.
Re: Cut in two piece
HelloPaul,Thanksforthisveryinterestinganswerinitsdesign,Itakegoodnote.Iam attachingapictureoftherepresentationofthepucksplitinhalfwiththea...
View ArticleClik here to view.
Re: Folding or bending of steel full bar
HelloAttached is amodelKind regards.Denis Necking of an Elastoplastic Metal Bar
View ArticleRe: Cut in two piece
HelloThank youforyournewshipment.I'mgoing to watch it.ButwhatIstilldon'tunderstand,iswhywhenIsimulateshalfapiecebytheplaneofsymmetry,Idonotgetthesameresults.Kind regards.Denis
View ArticleWhy did the iterations change?
Hi, I set up an elasto-plastic study of a strut that is gradually squashed using an enforced displacement. I did not know when things would get interesting and so applied a very long time history and...
View ArticleMonitoring iterative solutions
Hello again, Related to the earlier elasto-plastic question but also LDA, contact ... It is useful to be able to monitor the progress of an iterative study by reviewing the Pass 1 results as they...
View ArticleRe: Cut in two piece
Hello Denis, your model is wrong, half too,not constraints possible, contact only. RegardsPaul
View Articlecreo simulate 4.0中收敛图的纵坐标是什么意思
我在分析的结果文件夹中找到了一个文件：study.ldc（study为文件名），这个文件的内容跟收敛图的数据很接近。我对收敛图中的纵坐标不解，希望在这儿得到答案。
View ArticleClik here to view.
Re: Folding or bending of steel full bar
The size of the force is 245Nyou can use optimized design studies
View ArticleRe: Hope to add co-simulation interface with AMEsim in dynamic mechanism module
I've created a new thread here.Bye
View ArticleClik here to view.
Re: Mechanism's Custom Loads
Hello,PTC custom load interface is not easy for application engineer, you need to know how to do programming and you need to purchase TOOLKIT license too. I don't think that is a good solution.if you...
View Article