Re: Mechanism's Custom Loads
Custom Load functionality is devoted to situation when you should perform a co-simulation. That is to say if you have additional differential equation(s), and you want to integrate them together with...
View ArticleRe: Mechanism's Custom Loads
Hi Jason,you're right in talking about the right way to simulate a feedback loop, namely using amesim rather than Pro/mechanism.But in another postBoris Kirzhner told that you could use alo an external...
View ArticleClik here to view.
Import loads in Creo Simulate 3.0
Hello. I am facing a desperate situation right now.We received from our customer a 3D model and an excel file containing a point cloud from their CFD analysis. The excel file is structured. There are...
View ArticleRe: Creo Simulate vs ANSYS Workbench contact analysis w. friction.
Dear Mats,developing a contact algorithm with linear elements is already difficult. In a conventional scheme even quadratic elements rarely converge, and special formulations are needed like that of...
View ArticleRe: Import loads in Creo Simulate 3.0
Unfortunately No. Even we are facing a similar issue of importing loads from a spread sheet output from Adams, but not possible.See the below discussion. Import Load values from XLS
View ArticleRe: Import loads in Creo Simulate 3.0
Hi all, Today, Creo Simulate does not allow the automatic import of loads from an external file out of the box. We have worked closely with one of our development partner, AMC Bridge...
View ArticleRe: A bug about reviewing the total load?
There is still no fix about this bug in Creo4.0 Simulate, what a pity!
View ArticleClik here to view.
Re: A bug about reviewing the total load?
My English is poor,sometimes it's hard for me to express the bug,so perhaps you or someone else can help me to file this report,ok?
View ArticleClik here to view.
Re: Folding or bending of steel full bar
Hello 学 蒋Thankyouforyourresponse.Theblockagesonthe axisyoudoon"points"?Youhaveusedthemethodofoptimizeddesignstudies?Kind regards.Denis
View ArticleClik here to view.
Re: Folding or bending of steel full bar
"blockages " means constraint？I used the optimized designThe beam.prt.1 can be opened by creo 4.0
View ArticleRe: Folding or bending of steel full bar
HelloThank youforyourshipment.Yes,blockingmeansforced.I'monW732-bitpro,IdonotyetuseCreo4.0,sothatIbuyaPC64bitwithW10pro.Kind regards.Denis.
View ArticleClik here to view.
Re: Folding or bending of steel full bar
HelloHere'sanotherdemodonewith64-bitsoftware.Kind regards.Denis. http://cds.comsol.com/mg/c585a2fffbe78e.zip
View ArticleClik here to view.
Beam theory usid in Simulate
hi all, I'm trying to figure out what beam theory is used in Simulate with beam elements.Is it Timoshenko's theory is which a section can rotate or is it Eulers-Bernouillis theory in which a cross...
View ArticleCreo Simulate 4.0 (What's new)?
Happy new year! Anyone have a link to any information regarding what's new/changed in Creo Simulate 4.0? Thanks,Andy
View ArticleRe: Creo Simulate 4.0 (What's new)?
Creo Parametric Help Center https://www.ptc.com/~/media/Files/PDFs/CAD/Creo_4/Datasheet-Top_Enhancements_Creo_Parametric_4-en.pdf?la=en
View ArticleClik here to view.
Re: Creo Simulate 4.0 (What's new)?
The help center link was very helpful. Thank you for the prompt response
View ArticleClik here to view.
Re: Angle between shell normal and solid normal must be greater than 45 degrees
Garry, I know this is WAY late, but the only thought I have is that it could be due to the same reason of the May 15 comment here: Re: How to fix degenerate boundary faces in Simulate, where Creo just...
View ArticleClik here to view.
Re: Beam theory usid in Simulate
It's Timoshenko. You can verify this by creating a short beam and doing a comparison analysis between one with a Poisson's Ratio of 0.3 and another with -0.999 (the latter will behave like an...
View ArticleClik here to view.
Re: Folding or bending of steel full bar
Yes, Denis, it is possible to analyze this, but you will have to use solid elements with material plasticity, and also large deformation analysis + contact analysis. If you want to model the plastic...
View Article