Clik here to view.
Re: How to fix degenerate boundary faces in Simulate
Hi Erik, thanks for your suggestion, indeed could be the problem you mentioned because the surfaces ini my case could not meet perfectly at 90°.But last days I contacted the PTC support and they...
View ArticleRe: More than 32 Gbyte memory
Erik, I submitted a Product Idea over two years ago to increase the amount of RAM in Creo Simulate. Mark Fisher finally came back with a response, but when I questioned his response, he has yet to...
View ArticleRe: Why "Analyses and Design Studies" window status and "Run Status" summary...
Tommaso, Here is a post on the same topic: https://www.ptcusercommunity.com/thread/59768 I haven't seen this problem in Creo 3, but I've seen it in WF4 thru Creo 2.
View ArticleRe: More than 32 Gbyte memory
Even that can be a valid reason to not release it. Question is if you wish to accept a performance penalty for 99% of the users to accommodate 1% of the users that are now running into limitations of...
View ArticleRe: More than 32 Gbyte memory
Release it to whom? There's no reason not to release both.
View ArticleRe: More than 32 Gbyte memory
Hi Steven, I wasn't (haven't been) aware of this 16 Gb limit, I'm quite sure I already used up to 32 Gb, and seen crashes when the requirement was higher than that. I do not touch the memory...
View ArticleRe: Why "Analyses and Design Studies" window status and "Run Status" summary...
Ah ok, yes I knew the red flag button, didn't remember the message it indeed shows. thanksbye
View ArticleRe: Simulation status: Failed while calculating
Hi Domen, your problem just happened to me yesterday, for the first time (or the first time I recognized it) in 11 months.I opened a discussion on the same issue, since I had not seen your post, this...
View ArticleRe: Why "Analyses and Design Studies" window status and "Run Status" summary...
Hi Steven, thanks for your notice! bye
View ArticleRe: Simulation status: Failed while calculating
Thanks for your info. If you find anything usefull about this problem let me know.If the problem is repeatable, send it to PTC so they will investigate it. The solution to this problem was already...
View ArticleClik here to view.
Re: Simulation status: Failed while calculating
yes in fact as I wrote in the previous post I hadn't seen your post and posted a new one thinking no one had never talked about it... in fact at the end my simulation too went well and completed. bye
View ArticleClik here to view.
Any tips for dealing with mesh errors related to Conical Rounds?
Hoping someone has a few pointers with getting Conic Rounds to mesh in Creo Simulate?I have tried adjusting the settings of the round, adding auto geom edge distribution controls with no success.Any...
View ArticleQuestion regarding Gear Pairs in Mechanism
Hi, When defining a gear pair, you have to define the pitch circle diameters of both gears. In my case, the connection is a rack and pinion (simulating a pulley/rope train). However, when entering the...
View ArticleRe: Question regarding Gear Pairs in Mechanism
You can enter a user defined ratio. In case of the rack and pinion, it want to know a linear distance per rotation. I have run into some limitations in the rack and pinion where the servo axis has to...
View ArticleClik here to view.
Fasteners references edges definition error
Hallo, I have a problem with defining fasteners idealization in Simulate (Creo 2.0 M110). I have to define a fastener between two components, when I select the two corresponding edges, this error...
View ArticleRe: Question regarding Gear Pairs in Mechanism
Yes, the pulley rotation axis is perpendicular to the slider axis I'm using for the rope. Is the user defined ratio a parameter that I can drive using a relation? It seems to be simply another way of...
View ArticleRe: Fasteners references edges definition error
Tommaso, Try adding a surface region or volume region where the fastener bounderies are. This will give you a valid flat edge / line on the cylinder surface to select.Hope this helpsDon Anderson
View ArticleRe: Question regarding Gear Pairs in Mechanism
I haven't tried to find the parameters defined to user-defined gear ratios so I am not sure if it can be driven. However, you should be able to drive the ratio based on a feature, and the feature can...
View ArticleRe: Question regarding Gear Pairs in Mechanism
I went back and looked for the parameter that connects to the gear definition dialog and could not find it.It seems you should be able to select a feature to set the pitch diameter or drive the value...
View ArticleRe: Fasteners references edges definition error
The two corresponding edges must be parallel. I submitted a Product Idea to add countersink fasteners like Solidworks, but it hasn't received much attention.
View Article