Re: Transient Thermal Conduction - Creo Simulate
Tim, it seems you want to use Prescribed Temperature (20 degree) for the initial temperature.However, it is a constraint and will stay constant all through the analysis, so the surface can never reach...
View ArticleClik here to view.
Re: Mold Analysis Lite
Hello Douglas, my understanding is that the license has to be purchased in the past (until 17-oct-2014) to be eligible for upgrade. When they purchased it afterwards, they don't get CMA for free.And of...
View ArticleRe: Displacement is way too high
Thank you for the reply. I think the answer to your question is yes. That is, I am opening a design study with the part exactly as shown in my attached pictures and running the analysis. Here is the...
View ArticleRe: Displacement is way too high
Couldyoutellmewhatyouuse?Theconversionof young'smodulusisnotgood.
View ArticleClik here to view.
Re: Displacement is way too high
Lucas, SA-36 is steel, so change your E to 2.9e+07 psi. I used IPS units. But that should fix it, as you can see in the displacement plot below.
View ArticleRe: Displacement is way too high
Thank you Steven! That was it. The lbm/(in sec^2) unit was pulled in from out material file. I'll have to get those corrected. Now I'm curious if you think this is an adequate analysis of this part to...
View ArticleClik here to view.
Re: Displacement is way too high
Lucas, I ran your model with 5% and 1% convergence in the regions of interest. Remember, von Mises numbers are all positive in the legend, but I got about 30060 psi max in the lower and upper radii....
View ArticleRe: Displacement is way too high
Steven, Thanks again for your help. What I'm concerned about at this point is not the result of the analysis, but the method I've used to get there. The top hole is hung on a hook hanging on a chain...
View ArticleClik here to view.
Re: Displacement is way too high
Lucas, Can you upload a picture of the physical system? I don't know why you have a gravity load in the design study. If this is just a hook, constrained at one end with a bearing load at the other...
View ArticleRe: Displacement is way too high
Steven , I thought the gravity load was to include the weight of the part itself. I knew it would not have a significant effect on the result in this case, but included it just to be thorough. Is that...
View ArticleRe: Displacement is way too high
Excellent. Can you tell us what the three slotted hole are for?
View ArticleClik here to view.
Re: Displacement is way too high
You can Review Total Load before processing to check the loads in your model. Then you can check the resultant loads in the summary window in the post-processing phase.
View ArticleRe: Displacement is way too high
The slotted holes are hand-holds for manipulating the position of the part hanging from the hook while it is suspended - that would be primarily rotating it and fine adjustments to set it down in the...
View ArticleClik here to view.
mass idealization in modal and shock analysis
Hello,I am doing a shock analysis introducing as input a response spectre of a sismic event, function of frequency and acceleratio Se(T) [g].The idealization of a chemical reactor with the heat...
View ArticleClik here to view.
Re: Atlas Stress Strain Curves
HelloThereisaverycomprehensivesiteonmaterials.Itisfreefortesting,butafteritispaid.Itwould becompatiblewithCreotoretrievethedataofcurveswhichwould beagreatadvantage.Kind regards.Denis...
View ArticleRe: How to display reference plane or curve in mechanica analysis result?
Your comment seems to work, but I have not wholely been aware of your idea. I need to exercise that for times.
View ArticleClik here to view.
Re: Simulation non linéaire avec matériau élasto-plastique
Thanks a lot ! I think you have answerd to all my questions. Thanks to other guys, it's clear now ! Nevertheless, one week ago, I has a training on Ansys use (linear), and i will have the non linear...
View ArticleRe: In Optimization Design, how to select one part's parameters in assembly...
Sorry so late to reply you. I did not quite understand your proposal. How to operate it ?
View ArticleRe: In Optimization Design, how to select one part's parameters in assembly...
For example, if you want to drive the part parameter WIDTH in an assembly optimization:Create an assembly parameter PART_WIDTHCreate an assembly relation WIDTH:0 = PART_WIDTH (if session ID of part is...
View ArticleRe: Displacement is way too high
What's the overall factor of safety? My view would be that unless this is being designed right down to the limit (is it going into space? ) then minor additional loadcases such as that one can be...
View Article