Clik here to view.
Re: Non-symmetric results for symmetric model and load?
From a design point-of-view, what would be the difference in your margins of safety using symmetry/mapped meshing vs a perfectly coded software with 0% error?
View ArticleRe: Non-symmetric results for symmetric model and load?
Well done Agnes Anxious to find out what PTC will report on SPR 2258467. It should not have been possible. Everybody runs the majority of analyses with a default mesh and SPA. This should give decent...
View ArticleRe: File Extensions in Creo Simulate Analysis
Frank,If my suggestions have resolved the problem, could you mark the discussion as Correct. This will benefit others who are searching for solutions. Thanks.
View ArticleRe: meshing issue of 2D Plane
Alvin,If my suggestions have resolved the problem, could you mark the discussion as Correct. This will benefit others who are searching for solutions. Thanks.
View ArticleRe: Non-symmetric results for symmetric model and load?
Erik, I greatly appreciate you posting your findings, as it gives us all insight, and what not to do with a 360-degree cone with a pressure load, something I wasn’t aware of. If PTC has resolved your...
View ArticleRe: Analysis run not completing - help?
Problem diverted!Im not too sure if it is a bug or something Ive done?Basically I had an assembly (1 Housing + 2 Components + 2 Adhesives) with 2 simplified reps. The housing was common to both reps.I...
View ArticleClik here to view.
Re: Analysis run not completing - help?
So you answered your own question. Can you mark your own question as Correct?
View ArticleRe: Simulation status: Failed while calculating
There had been a reproducible case in the past and of course it had been investigated by TS (it was fixed within Creo Elements/Pro 5.0, see CS22232)So the issue you see, seems to be similar, but not...
View ArticleRe: "No analysis is associated with the limit on measure..."
I found one single occurrence of this error message in our database. Investigation in R&D showed that it was due to a model corruption.To fix the model, remove the design limit row that causes the...
View ArticleRe: Analysis run not completing - help?
Im not convinced the problem has been answered.I still dont know why I had the problem, other than its link to simplified reps?
View ArticleRe: "No analysis is associated with the limit on measure..."
Thanks Gunter. Unfortunately I've moved on from that model now so I don't have like-for-like to verify, but I'll remember this in case it happens again!
View ArticleWhere can I find the Natural Frequency of a system in Mechanisms?
I'm assuming it must calculate it?Just the first one would be fine. Thanks,Cameron
View ArticleRe: Simulation status: Failed while calculating
The problem is that I can`t reproduce it. At some point it just stared working fine.Anyway,...the main thing is, as I wrote in the previous post, that the results where the same, no matter if the...
View ArticleRe: Simulation status: Failed while calculating
Gunter Koch wrote:I had also observed in past releases, that when I left Mechanica mode while running an analysis, then returning to Mechanica (now Simulate), the run status was no longer showing,...
View ArticleCreating a part with multiple material layers
I am looking to create a part in Creo that represents a metallised plastic part. The base material is made from a plastic material and it has a very thin (10um) copper layer on top of the plastic with...
View ArticleRe: Creating a part with multiple material layers
You are describing an assembly of different materials; there's not an option to have a part do this.
View ArticleClik here to view.
Re: Creating a part with multiple material layers
Hello,CalumYourthicknesses areso smallthat Ido not know ifCreowillsee.Ithink we will haveto increase the accuracyof your partsto its maximum,haveyou ever tried.Nowis what thesethin layerswill...
View ArticleRe: Measures show incorrect values
Material assignments could happen in component model or at assembly level to the component feature - maybe some conflict?
View ArticleRe: Creating a part with multiple material layers
Yes, you will need to set the accuracy significantly higher... maybe set it to absolute depending on the part size. To have different materials, you will need some kind of assembly. That is the only...
View Article