Re: What is best practice for FEA of assemblies?
Did you have intf3d_in_as_part set to yes when you imported the step file? If not then change that and try it again. If you are looking for how to keep a simulate model separate from the design model...
View ArticleClik here to view.
Re: What is best practice for FEA of assemblies?
hi my method: exmaple fea_asm.zip regardspaul info (german) attached
View ArticleRe: What is best practice for FEA of assemblies?
Hallo PaulThank you for the model you uploaded. I could not figure out how to do the copy and solidify step, but I found an equally simple method: Insert-Shared Data-Merge/inheritance. Maybe you use a...
View ArticleClik here to view.
Re: What is best practice for FEA of assemblies?
my method is without AAX:STRG+CSTRG+VENTEREDIT->SOLIDIFY... (Wildfire 5)ENTERSTRG+AregardsPaul
View ArticleClik here to view.
Max. Von Mises stress Fringe vs. Measure
Hello! I am calculating a truss simulation of a 3d Structure with L-Profiles.I have set the idealizations for beams, constraint sets, loads, etc.After the Statich analysis, I can review the Max VM...
View ArticleClik here to view.
How to use the FFT of Acceleration Data in Dynamic Frequency Analysis and...
How to use the FFT of Acceleration Data of three directions in Dynamic Frequency Analysis and Dynamic Random Analysis?Our product is an electronic box with two fans. We have obtained data about their...
View ArticleRe: What is best practice for FEA of assemblies?
Ok, now I get it.I am not sure if my method requires AAX, but I think that the results are pretty much the sameFor Info to other users with keybords that are similar to mine:In Pauls description STRG+C...
View ArticleRe: Creo Simulate Multicore Calculation
Hi, we had the same questions 2 years ago, but no real solution. swerner-2 you write about "30 minute simulation" time. This sounds very short. maybe the part is so small, that a distribution over more...
View ArticleClik here to view.
Re: Max. Von Mises stress Fringe vs. Measure
This has been a known problem for many years, going way back to the Pro|Mechanica days. I have encounter this many times, and I have submitted tech support calls, and tech support has never been able...
View ArticleRe: Creo Simulate Multicore Calculation
Why?It's a nonsense....But this is for linear AND non linear analysis?
View ArticleRe: Creo Simulate Multicore Calculation
hmm maybe they use more GPU Power or have improved the code for very small Simulations. But not using parallel computing for simulations seems quite unbelievable.br Bernhard
View ArticleRe: Max. Von Mises stress Fringe vs. Measure
Hello! You are right, the values on the summary do not contradict each other.I noticed this error when I checked the value of the measure and I saw that it was greater than the Max-Value in Fringe...
View ArticleRe: Max. Von Mises stress Fringe vs. Measure
You're using beam elements, and the way you select your results based upon the orientations could have something to do with it. I have not seen this problem using beam elements, but I have seen it...
View ArticleClik here to view.
Re: Creo Simulate Multicore Calculation
simulate has more solver, linear and nonlinear, but this:is very old solver, inaccurate... block solver (static, contact [nonlinear] etc): multithreading automaticaly,but not after creo 3 m120 ......
View ArticleRe: Max. Von Mises stress Fringe vs. Measure
Hello I would open a ticket to PTC but I do not know how to do it. Should I do it here in PTC-community or how does it work? Thank you very much
View ArticleRe: Creo Simulate Multicore Calculation
This is very worrying. I've just run an analysis (also contact) in M070 which has taken 0.6 hours elapsed but 1.6 hours CPU time - I don't want this to take an extra hour every time I run it! It...
View ArticleClik here to view.
Re: Max. Von Mises stress Fringe vs. Measure
There are three ways you can do this. 1. You can create a support ticket right from Creo, if you're online. Take a look at the image below and just follow the instructions. 2. You can log a case...
View ArticleClik here to view.
Re: Extract measures data to plot in Excel
Thank you so much. You have been a big help. Richard Hilson
View Article